Steps // How to Lay a Stone Tile Floor
1 ×

Cut the Membrane

 
Step One // How to Lay a Stone Tile Floor

Cut the Membrane

how to lay a stone-tile floor roll out plastic membrane
Photo by Wendell T. Webber

Starting in a corner, roll out the membrane, flocked-side down, beside the room's long wall. At the end wall, crease the roll into the corner, as shown, and cut along that crease with a utility knife. Trim as needed to get around pipes, ducts, and doorways. Lay out and cut the remaining sections so that their edges butt together and they cover the entire floor.

 
2 ×

Spread the Thinset

 
Step Two // How to Lay a Stone Tile Floor

Spread the Thinset

how to lay a stone-tile floor spread out thinset
Photo by Wendell T. Webber

Number the sections, set them aside, then vacuum the floor. Mix a batch of thinset: Use polymer-modified thinset on plywood and unmodified thinset on cement-based substrates. Starting at a corner, spread the mix evenly over a 6-foot section as wide as the membrane, then comb it into long parallel furrows with a ¼-inch notched trowel, as shown.

 
3 ×

Roll Out the Membrane

 
Step Three // How to Lay a Stone Tile Floor

Roll Out the Membrane

how to lay a stone-tile floor roll out the membrane
Photo by Wendell T. Webber

Don't let the thinset sit—any delay could prevent a good bond. Butt the first membrane section into the corner and immediately roll it out onto the fresh thinset. Spread and comb out another 6-foot section of thinset, and unroll the next portion of the membrane onto it. Repeat until the first roll reaches the end wall.

 
4 ×

Secure the Membrane

 
Step Four // How to Lay a Stone Tile Floor

Secure the Membrane

how to lay a stone-tile floor secure the membrane
Photo by Wendell T. Webber

Immediately after the membrane is laid, use a grout float to press every square inch firmly into the thinset, as shown. Do the same after laying each remaining section. Once the entire floor is covered, dry-lay a line of tiles between each pair of walls to judge how best to minimize cuts and get a pleasing layout. Pick a starting point that will keep you from stepping on stones after they're laid.

 
5 ×

Lay the Tiles

 
Step Five // How to Lay a Stone Tile Floor

Lay the Tiles

how to lay a stone-tile floor lay the slate tiles
Photo by Wendell T. Webber

Spread unmodified thinset over an area about 3 feet by 16 inches, filling the membrane's square dimples. Comb out parallel ridges with the notched trowel. For each tile, smear thinset on its underside, press it firmly in place, and make sure it's flush with its neighbors and that the joints are even. Gently remove excess thinset from the joints with a putty knife, and swab the stones with a damp sponge.

 
6 ×

Grout the Joints

 
Step Six // How to Lay a Stone Tile Floor

Grout the Joints

how to lay a stone-tile floor grout the joints
Photo by Wendell T. Webber

The next day, wash away thinset residue with muriatic acid, and, to protect the stone from grout stains, apply a sealer. When that's dry, mix up a sanded grout and push it diagonally into the joints with a grout float. Wait 10 minutes, then wipe off grout residue from the stone with a damp sponge, rinsing it often. Don't disturb the joints. The next day, rub off any haze with cheesecloth and wipe on a final sealer coat.

 

Shop Related Products

$9.99 $9.99 prime

$18.95 $18.95 prime

$11.82 $11.82 prime

$7.54 $14.93 prime

$6.27 $6.99 prime

$3.59 $12.76

$9.19 $9.47 prime

$3.28 $3.29 prime
 

Sponsored Stories

TV Listings

Find TV listings for - saboteamos.info and Ask - saboteamos.info in your area.