Steps // How to Build a Table from Salvaged Beams
1 ×

Overview for Building a Table from Salvaged Beams

 
Step One // How to Build a Table from Salvaged Beams

Overview for Building a Table from Salvaged Beams

illustration of salvage project table framing
Illustration by Douglas Adams

Much the way a picnic-table top is constructed, I joined three reclaimed beams from below using 2x8 wood straps secured with 5/16-by-3½-inch lag screws. The industrial-look base is made from ¾-inch gas pipe and coordinating elbows, tees, and flanges, all from the home center. Download a blueprint for the base.

 
2 ×

Assemble the Pipe Base

 
Step Two // How to Build a Table from Salvaged Beams

Assemble the Pipe Base

assemble the pipe base to build a table from salvage beams
Photo by Kristine Larsen

By doing a dry fit with the base resting on the beams and straps, you can ensure proper alignment by loosening or tightening the fittings. Length and width can vary, but table height is typically 28 to 30 inches.

 
3 ×

Cut the Two Wood Straps

 
Step Three // How to Build a Table from Salvaged Beams

Cut the Two Wood Straps

Cut the Two Wood Straps to build a table from salvage beams
Photo by Kristine Larsen

Cut the two wood straps, and bevel the ends using a compound miter saw. The straps should be a few inches shorter than the width of the three beams clamped edge to edge.

 
4 ×

How Long is Too Long

 
Step Four // How to Build a Table from Salvaged Beams

How Long is Too Long

determine the length of the top to build a table from salvage beams
Photo by Kristine Larsen

Determine the length of the top, and use a T-square and pencil to mark cutlines across the face of the beams on both ends.

 
5 ×

Cut the Beams

 
Step Five // How to Build a Table from Salvaged Beams

Cut the Beams

cut the beams to build a table from salvage beams
Photo by Kristine Larsen

With the beams faceup and clamped edge to edge, use a circular saw to make a straight 90-degree cut along your pencil line on each end. Flip the beams facedown, and bevel the bottom edges by adjusting the blade on your circular saw to a 45-degree angle (shown). The bevel gives a beefy top a lighter, more finished look.

 
6 ×

Secure the Straps

 
Step Six // How to Build a Table from Salvaged Beams

Secure the Straps

secure the straps to build a table from salvage beams
Photo by Kristine Larsen

Clamp the straps to the beams, and drill pilot holes for the lag screws, staggering them every 4 inches. Use a spade bit to bore recesses for the screwheads, and twist in the fasteners with a socket wrench.

 
7 ×

Attach the Base

 
Step Seven // How to Build a Table from Salvaged Beams

Attach the Base

attach the base to build a table from salvage beams
Photo by Kristine Larsen

Position the connecting flange for each of the four legs on top of the straps, and mark the screw holes. Remove the base, and drill pilot holes at the marks for ¼-by-2½-inch wood screws. Replace the base and drive in the screws.

 
8 ×

Sand the Top

 
Step Eight // How to Build a Table from Salvaged Beams

Sand the Top

sand the top to build a table from salvage beams
Photo by Kristine Larsen

Turn the table right-side up and, wearing a dust mask and protective glasses, use a random-orbit sander fitted with 60- or 80-grit paper to remove the rough top layer. Follow with a finer grit to smooth it.

 
9 ×

Complete the Table

 
Step Nine // How to Build a Table from Salvaged Beams

Complete the Table

final steps to build a table from salvage beams
Photo by Kristine Larsen

Complete the table by applying shellac to darken the wood and seal it. Let dry, and follow with a coat of beeswax polish to fill surface cracks. Now gather your friends for a celebratory potluck to christen your new table.

 

Shop Related Products

$93.00 $98.25 prime

Too low to display $239.00 prime

$8.50 $15.00 prime

$3.48 $10.34

$19.99 $30.99 prime

$49.98 $59.99 prime

$9.99 $9.99

$34.87 $34.87 prime
 

Sponsored Stories

TV Listings

Find TV listings for - saboteamos.info and Ask - saboteamos.info in your area.