man testing efficiency of furnace
Steps // How to Do Fall Furnace Maintenance
1 ×

Shutting down the System

 
Step One // How to Do Fall Furnace Maintenance

Shutting down the System

man turning off electrical power for furnace repair
Photo by Keller & Keller

Before performing DIY furnace maintenance, Richard makes sure to switch off the electrical power and the fuel supply. The distinctive red power switchplate can usually be found at the top of the cellar stairs or near the burner itself, while the fuel shutoff valve is near the oil tank or on the incoming gas pipe. Note the location of both in case of a future leak or fire.

 
2 ×

Cleaning the Combustion Chamber

 
Step Two // How to Do Fall Furnace Maintenance

Cleaning the Combustion Chamber

man scraping out built up carbon from furnace
Photo by Keller & Keller

In the combustion chamber, fuel mixes with air and is ignited, generating heat—as well as carbon soot, water vapor, carbon dioxide, and worse. A buildup of soot can cause the chamber walls to corrode. Richard scrapes out built-up carbon using a small wire brush. Then he removes loose material with an industrial shop vacuum and inspects the chamber for holes or corrosion before replacing the cover.

 
3 ×

Inspecting the Flue Pipe

 
Step Three // How to Do Fall Furnace Maintenance

Inspecting the Flue Pipe

man inspecting flue pipe of furnace
Photo by Keller & Keller

Richard checks for holes in the exhaust flue that could leak carbon monoxide, particularly where the pipe meets the furnace. Small holes can be patched with foil tape, but corroded flues must be replaced. He also adjusts the flue pipe's barometric damper, which moderates the chimney draw. "A big, tall chimney in an old house tends to suck too much air, compromising efficiency," he says. "Your service pro can weight the damper to lessen the draw.

 
4 ×

Replacing the Oil Filter

 
Step Four // How to Do Fall Furnace Maintenance

Replacing the Oil Filter

man replacing oil filter of furnace
Photo by Keller & Keller

The oil filter (found in oil-powered systems only) prevents small impurities from clogging the oil-burner nozzle, which could result in a misfire that shuts down the system. Richard first closes the oil valve, then removes the old filter and replaces it, setting aside the dirty filter to be disposed of according to local hazardous-waste regulations.

 
5 ×

Changing the Air Filter

 
Step Five // How to Do Fall Furnace Maintenance

Changing the Air Filter

man replacing air filter of furnace
Photo by Keller & Keller

"During the winter, all the air that your family is breathing comes through this filter," says Richard. "You can't change it too often, but never let it go for more than a year." Changing the filter is something any homeowner can do easily. At the same time, Richard checks the blower belt's wear and tension. (The blower, driven by an electric motor, moves heated air from the furnace through ductwork to room vents.) A loose belt can slow the blower, compromising efficiency. If the belt deflects more than ¾ inch when pressed firmly, it can be adjusted by sliding the motor backward slightly.

 
6 ×

Adjusting the Burner and Testing Efficiency

 
Step Six // How to Do Fall Furnace Maintenance

Adjusting the Burner and Testing Efficiency

man adjusting furnace burner and testing efficiency
Photo by Keller & Keller

Richard sets up a combustion analyzer, which calculates furnace efficiency by measuring gasses in the exhaust flue. He makes sure that the burner's air gates are adjusted for the proper ration of fuel to air. "You want the fuel that you've brought to the be burned before it goes up the chimney," Richard says. He also replaces the oil nozzle, which atomizes the fuel just before it ignites, and checks the flame color and shape at the igniter. For either oil or gas, this is a key indicator of stable and complete combustion. In a gas system, this is the time when the burner tubes should be vacuumed clean.

 
7 ×

Cleaning Floor Vents

 
Step Seven // How to Do Fall Furnace Maintenance

Cleaning Floor Vents

man inspecting floor vents
Photo by Keller & Keller

The fall is a good time for homeowners to remove floor registers and vacuum out the ducts, which are magnets for dust, pet hair, small toys, and food scraps. All of this reduces its efficiency, forcing you to crank up the heat. You'll also breathe a little easier without this debris in the air.

 

Shop Related Products

$14.97 $14.97 prime

$142.34 $159.74 prime

$64.99 $74.99 prime

$16.11 $16.11 prime
 

Sponsored Stories

TV Listings

Find TV listings for - saboteamos.info and Ask - saboteamos.info in your area.